Description

R-122 MKII
The R-122 MK II is a second-generation design of the venerable R-122 active ribbon mic. It shares the original mic’s ribbon geometry, transformer and impedance matching circuitry with condenser-like output levels that allow the R-122 to be used on even the quietest sound sources. It can also be paired to virtually any preamplifier.
The R-122 MKII takes the R-122 to a whole new level, delivering unprecedented flexibility for ribbons with the addition of a switchable -15 dB pad and a switchable bass-cut filter. The switches are completely out of the circuit when disengaged so when both are off, the microphone is for all purposes an original R-122. The switches are located on the back of the microphone and recessed to prevent accidental activation.
Sling-Shock RSM-SS1
The Sling-Shock (Patent No. 8,571,250) is a revolutionary departure from traditional shockmount designs. Royer has done away with unreliable rubberised parts and elastic cords, producing a durable shockmount that provides exceptional isolation from vibration, rumble and resonances.
Royers proprietary system of non-resonant nylon cable and damped steel springs acts to isolate the microphone from vibrations induced from the microphone stand. These vibrations appear as rumble and/or low-grade noise across the bandwidth and are greatly reduced by use of the Sling-Shock.
Sling-Shocks also eliminate the self-resonance that traditional shockmounts can generate on high SPL applications like -miked electric guitar. Shockmount self-resonance creates harmonic interference at various frequencies – Sling-Shocks eliminate the issue. The Sling-Shock’s superior vibration-reduction capabilities and lack of self-resonance allow engineers to capture performances free of vibration-related interference across the bandwidth.
The Sling-Shock RSM-SS1 is sized to fit Royer’s 1-inch diameter ribbon mics; R-121, R-122 MKll, R-122V and SF-12 ribbon microphones. The RSM-SS1 will work with any cylindrical microphone measuring approximately one inch in diameter (+/- 1/8 inch).
R-122 MKII Features
Phantom powered circuitry provides high output and impedance matching
-15 dB pad before the mics electronics gives more headroom when activated.
Bass cut filter reduces proximity effect and bass below 100 Hz when activated
High SPL Capabilities
No distortion up to maximum SPL rating
Extremely low residual noise
Ribbon element is not affected by heat or humidity
Absence of high frequency phase distortion
Equal sensitivity from front or back of element
Consistent frequency response regardless of distance
Rear side of mic records slightly brighter when three feet or closer to sound source
Sling-Shock RSM-SS1 Features
Superior isolation from vibration, shock and rumble
Lack of self-resonance on high SPL applications
Felt-lined, scratch-free microphone chamber holds mic securely
No rubberised parts to degrade or stretch
Built in microphone cable clip minimises cable-related vibration
Flexible for easy microphone positioning
Lifetime manufacturers warranty
R-122 MKII Specifications
Acoustic Operating Principle: Electrodynamic pressure gradient with active electronics
Polar Pattern: Figure-8
Generating Element: 2.5-micron aluminum ribbon
Magnets: Rare Earth Neodymium
Frequency Response: 30 – 15,000 Hz 3 dB
Sensitivity: -36 dB (re. 1v/pa 1 dB)
Switchable Pad: -15 dB
Switchable Bass Cut: 100 Hz (6 dB per octave)
Self-Noise: < 18 dB
Output Impedance: 200 Ohms, balanced
Output Connector: Male XLR 3-pin (Pin 2 Hot)
Rated Load Impedance: 1K-Ohm minimum
Maximum SPL: 135 dB @ 30 Hz
Power Requirements: 48-Volt Phantom Only
Supply Current: 4 mA
Dimensions: 206mm L X 25mm W (8 1/8 L X 1 W)
Weight: 309 grams (10.9 oz)
Finish: Burnished Satin Nickel